 |
 |
||
|
|
|
||
|
|
 |
|||||||
| Scale 2.2's Discuss your scale trucks that use 2.2" sized tires. TLT based and similar. |
 |
|
|
Thread Tools | Display Modes |
|
#46
03-09-2017, 08:49 AM
|
||||
|
||||
Yesterday I was trying to weld the music wire to the cage for the fabric roof support
 Problems with the heat affected zone being brittle meant any time it gets bumped the welds break. That's no good. So today I popped off the wire, did a little grinding and welded nuts to the cage  This let me use two pieces of music wire to make the loop without any brittle spots  I also got some pre-wired 10mm LED's in red and white, but I didn't realize they were 12mm tall. No biggie, chucked them up in the lathe and turned them down.  Not the original square lights, but they'll work ok  Sent from my iPhone using Tapatalk
__________________
This forum requires that you wait 30 seconds between searches. Please try again in 18 seconds. 
|
| Sponsored Links |
| The sponsored ad above is only displayed to guests. Creat an account today to remove this ad! |
|
#47
03-10-2017, 04:48 PM
|
||||
|
||||
|
.
Wow! Coming along nice! .
__________________
 -Never trouble trouble, till trouble troubles you.
|
|
#48
03-11-2017, 10:44 AM
|
||||
|
||||
|
Got the top on
    Sent from my iPhone using Tapatalk
__________________
This forum requires that you wait 30 seconds between searches. Please try again in 18 seconds.
|
|
#49
03-11-2017, 02:43 PM
|
||||
|
||||
|
Awesome job, looks just like the original.
|
|
#50
03-13-2017, 07:11 PM
|
||||
|
||||
|
Thanks!
Well there were no easy ways around it. So I cut the grill off to get to the servo so I could make mounts. I cut and bent some sheet metal, then welded some M3 nuts to it  After getting both sides done I bolted the servo on  I ended up welding the servo mounts in place while bolted to the servo then hosing them with my squirt bottle to keep from burning the servo. Next I welded bolts to the end of the frame pieces and drilled holes in the grill to bolt it back on so I can get to the servo in the future. Sent from my iPhone using Tapatalk
__________________
This forum requires that you wait 30 seconds between searches. Please try again in 18 seconds.
|
|
#51
03-16-2017, 07:23 PM
|
||||
|
||||
|
Ok, so I got some shifters made, put in some carpet and got a dash cut out but not installed
 I also masked off everything and gave the cage a fresh coat of black. Then I got my lights wired up.   I drug it home and ran it around a bit. She wheels pretty good for a 10.5 lb rig.          Sent from my iPhone using Tapatalk
__________________
This forum requires that you wait 30 seconds between searches. Please try again in 18 seconds.
|
|
#52
04-02-2017, 08:09 PM
|
||||
|
||||
|
Got my dash and wheel in a week ago, and got to run a full pack through it yesterday
        Elvis brought over his CrossRC military for its maiden voyage too. Sent from my iPhone using Tapatalk
__________________
This forum requires that you wait 30 seconds between searches. Please try again in 18 seconds.
|
|
#53
04-03-2017, 08:29 PM
|
||||
|
||||
|
.
Very nice!  .
__________________
-Never trouble trouble, till trouble troubles you.
|
|
#54
04-04-2017, 05:36 AM
|
||||
|
||||
|
And even better, I replaced the 10ish kgcm servo and 3/4" plastic horn with a 15kgcm servo and 1" aluminum horn so now it even steers!
Sent from my iPhone using Tapatalk
__________________
This forum requires that you wait 30 seconds between searches. Please try again in 18 seconds.
|
|
#56
05-25-2019, 12:09 PM
|
||||
|
||||
|
Very nice work, I see you still got the skills bro. That cage is wicked.
Sent from my SM-N950U using Tapatalk
__________________
|
|
#57
06-09-2019, 08:45 PM
|
||||
|
||||
|
Thanks! I still really like the rig.
Sent from my iPhone using Tapatalk
__________________
This forum requires that you wait 30 seconds between searches. Please try again in 18 seconds.
|
|
| Thread Tools | |
| Display Modes | |
|
|
|
|
Linear Mode
